LH0036 DATASHEET PDF

July 11, 2019 posted by

The INA is a low power, dual instrumentation amplifier offering excellent accuracy. Its versatile. 3-op amp design and small size make it ideal for a. Part No.:, LH Download:, Download Right selection Save Target As View Datasheet (Html) No need to install PDF reader software. Description. Request National Semiconductor Corporation lh Instrumentation Amplifier, single,bipolar,quad,12pin,metal online from Elcodis, view and download lh .

Author: Kajisar Zutaur
Country: Australia
Language: English (Spanish)
Genre: Science
Published (Last): 3 September 2004
Pages: 439
PDF File Size: 19.75 Mb
ePub File Size: 12.89 Mb
ISBN: 403-9-22420-844-7
Downloads: 28550
Price: Free* [*Free Regsitration Required]
Uploader: Dozshura

Figure 3 is plot of slew rate versus Raw.

(PDF) LH0036 Datasheet download

The LH exhibits input bias currents typically. The LH is a 2 stage amplifier with a high. National Semiconductor Electronic Components Datasheet. National Semiconductor Electronic Components Datasheet. Operational amplifier, A” receives. For the LH, equation 4 reduces to: Figure 11 is a plot of bandwidth versus RB.

In the standard configuration, pin 1 of datashdet LH An internal factory trimmed resistor, R6, will. Should a higher CMRR be desired, pin 9 should be left open and the procedure, in this section followed. The implication is that a finite impedance must be supplied between the input and power supply ground.

Equation 5a re-arranged in more convenient form may be used to select RG for a desired gain: The source impedance looking into pin 2 is approximately 15 kD. LlW 10k k 1. Guard Pin With Buffer. Should a higher CMRR be desired, pin 9 should. In applications in which the signal source is float. The amplifier’s slew rate in this configuration is typically O. It also should be noted that large signal bandwidth. For applications requiring a lower source impedance. In some applications, particularly at low frequency, it may be desirable to limit bandwidth in order to mini- mize the overall noise bandwidth of the device.

  IMM 1344B PDF

Common Mode Range 10V for. Pin 2 of the LH is provided as a guard drive. G 4 As can be seen for identically matched resistors, eCM is cancelled out, and the differential gain is dictated by equation 4. A resistor Raw may be placed between pin 1 and ground to accomplish this purpose. Pin 2 will always be biased at the input common. Pin 2 will always be biased at the input common mode voltage.

Pin 9 should be grounded for nominal operation.

Under worst case conditions: Bias Current Return Path. This current must flow through Rise as shown in Figure The amplifier’s slew rate in. Off-set may be nulled using the circuit shown in. The value of the resistor is dictated by. Rise causing a voltage rise at point A. The source impedance looking into. LH may be inserted between pin 2 and the. Bandwidth vs Raw It also should be noted that large signal bandwidth and slew rate may be adjusted down by use of Raw.

  JOHN TAGG THE DISCIPLINARY FRAME PDF

Simplified LH The LH is a 2 stage amplifier with a high input impedance gain stage comprised of A, and -A 2 and a differential to single-ended unity gain stage, A3. Figure 2 shows typical small signal bandwidth versus R BW. As can be seen for lh003 matched resistors.

LH Datasheet PDF

Proper use of the. The implication is that a finite impedance must. The value of the datashheet is dictated by the maximum input bias current, and the common mode voltage. Use of Guard For applications requiring a lower source impedance than 15′ kD, a unity gain buffer, such as the LH may be inserted between pin 2 and the input shields as shown in Figure Figure 11 is a.

Pin 8 is also used to improve the common mode.

LH0036 Datasheet PDF

Figure 10 is a plot of input bias current versus. The closed loop gain may be set to any value from. A, also receives input e2 via A2 and R2. By similar analysis V,2 is seen to be: