June 9, 2019 posted by

B SERVICE MANUAL , REV C Thank you for your purchase of the B Keurig Single Cup Brewing System! U U The B is the. the Cleaning Instructions in this guide. Turn off and unplug the brewer before cleaning or maintenance. Allow to cool before putting on or taking off parts. Download KEURIG B SM service manual & repair info for electronics experts.

Author: Jurn Kagalkree
Country: Guatemala
Language: English (Spanish)
Genre: Automotive
Published (Last): 23 August 2015
Pages: 303
PDF File Size: 3.99 Mb
ePub File Size: 20.77 Mb
ISBN: 646-1-50317-189-9
Downloads: 38489
Price: Free* [*Free Regsitration Required]
Uploader: Dushakar

Push the cover back slightly and lift up to remove.

The mechanism is shown outside ofthe coin accessory cabinet. Attach coin changer unit to brewer per assembly instructions. The cold water tank is allowed to fill approximately 16 ounces, milliliters and then the valve mqnual is de-energized b3000 by the CWT float magnet proximity switch [Z] which controls the fill level. De-scaling If you are experiencing any problems with pump or similar your Brewer, please contact you Keurig Step 2: The Door Module can now be removed.

Risk of electric shock. The product should be connected to a branch circuit protected at maximum 20A. Unlock the coin changer cabinet fascia [Figure 11] and remove it by lifting up at coin retrievalopening [Figure 12].

The B contains real-time error detection. Looking at the left side of the brewer when facing from the front, locate the main power harness, and transformer. Install Kuerig Fig 4.


Once the menu is accessed the display will look like this set language: The water supply in the tank is fed through two check valve [M] and tubing to the two cold water pumps CWP [W] that supply water to the hot water tanks via the CWP elbow, CWP connectors, silicone tubing, multi-connector tee, manula silicone tube. Looking at the right side of the brewer, take note of the cutout in the chassis near the top.


Posted on Feb 07, Be the first mamual answer. The step by step procedure for installing the coin changer is as follows: Don’t show me this message again.

Attach the Puncture Mechanism Module cover and tighten its retaining screws. Loosen the large plastic nut at the bottom of the valve assembly. The K-Cup holder will open towards you. The power may be cycled to attempt to clear theerror, but if it occurs again, the same message will be displayed. Turn off water supply. The brewer must be primed for its first use as set forth below. Page 22 for brewers with serial number msnual up.

The large Plastic Nut must be tight.

By looking at the error code being displayed and reading the diagnostic chart provided in this manual, or hitting the Menu Button page 19 for brewers up to serial numberpage 22 for brewers with serial number and up once, you will be able to determine which module needs to be replaced.

These are captive screws sothey will NOT come out completely. De-Scaling Your BrewerMineral content in water varies from place to place. I fixed this problem in my Keurig with a paper clip. When reinstalling the new Coin changer cabinet Brewer manuzl platform High capacity platform Brewer-cabinet plate Accessory package A. If pass, Opens VV. There is extremely hot water in the K-Cup holder during the brew process.

Look at the back of the Control Panel module, you will see the wire harness connector and mznual hose union. For Back Panel removal when both side jeurig are removed loosen the four screws on the back panel and remove. This completes the LEFT side bin sensor removal.


Failure to do so will cause a leak when the hot water feature is selected. Diagnostics — Error Codes: Connect patch cable to female RJ11 connectors on keeurig back of the B brewer and the coin unit.

Push the cover back slightly and lift up to remove. Disconnect the Multi Connector Tee manifold from the old Power Module and add to the replacement unit.

Keurig B3000 Coffeemaker User Manual

If it is easier, you can remove the Puncture Mechanism Module completely to gain access to this connector. This warranty gives you specific legal rights, and you may also have other rights that vary from state to state and, in the msnual of Canada, from Province to Province. The functionality was tested by manufacturing. Before disconnecting the two hoses on top of the module, make a note of where they are attached. You do not needto remove keurib Control Module or disconnect any connections.

To brew, the system is closed, vent valve [J] de-energized and the brew pump [G] is energized. Disconnect the bin sensor. Once the menu is accessed the display will look like this set language: At the keeurig of the brewing process the image below will be displayed for 4 seconds. The menu button is located inside the brewer at the top see figure 1. The next screen will look like this error code.

Update your browser

Also look at the videos tab. The next screen will look like this set service phone.

Keurig B50 Coffee Maker Questions. Page 84 Fig 5.