ISO 16047 PDF

July 9, 2019 posted by

according to test requirements such as BS Pt. 2 or ISO This can be expressed in two ways, the Coefficient of Friction µ and the Torque Coefficient (K . ISO FASTENERS – TORQUE/CLAMP FORCE TESTING. DIN EN ISO Fasteners – Torque/clamp force testing (ISO + Amd ) (includes Amendment).

Author: Toran Kilrajas
Country: Martinique
Language: English (Spanish)
Genre: Science
Published (Last): 14 April 2009
Pages: 177
PDF File Size: 13.6 Mb
ePub File Size: 20.82 Mb
ISBN: 527-4-89843-930-3
Downloads: 95433
Price: Free* [*Free Regsitration Required]
Uploader: Fem

Because if bolts and screws are too loose, components may move. Please first log in with a verified email before subscribing to alerts.

BS EN ISO 16047:2005+A1:2012

However, if the fastener and with it the washer is isoo with a lubricant, the lubricated base of the fastener is tightened against the lubricated washer on the test bench.

If fasteners are lubricated, friction is reduced — this applies both with regard to both external lubrication via grease or wax and integrated lubrication via the addition of a lubricant to the coating. Nevertheless, coefficients of friction are determined for these parts. With these fasteners a washer is threaded onto the blank; the subsequent cold forming in which the thread is rolled into the surface ensures that this washer cannot fall off.

Coat thickness and coat thickness measurement. 1607

Coefficients of friction cannot be specified using measurement technology. Read more about subscriptions.

We have capability to collect time synchronized data across multiple instruments and sensors including the following:. For hard bases the standard prescribes a narrow range of hardness, but permits a broad range of hardness for soft bases.

Instructions for resetting the password oso be immediately emailed to you. These are then tightened with the same torque, although the coefficient of friction of the fasteners with captive washers is lower.


Torque to Yield Tests MEC can be 61047 tests on actual fastened assemblies to obtain torque-angle graphs and to establish the torque to reach the yield strength of the bolt. Simple instrumented fixtures with manual testing and data capture Automated testing of complex systems with customized control dashboards and reports.

Surfaces often have a major influence on this. For example, brighteners in the galvanised coat serve to lower the friction between reference part and fastener. Standards monitoring is a free service designed for you who wish to be alerted of changes to or new editions of the standards required in your work.

BS EN ISO +A – Fasteners. Torque/clamp force testing

Subscription pricing is determined by: Please enter your username or email address. Not only can FEA show where new ixo may have potential issues, it can be used to diagnose failures seen in the field, and also to optimize designs in order to reduce cost.

The moment new editions of the standards you monitor are released, changes are made, or appendixes are published, you will be alerted by email. Some of the capabilities at Matrix Engineering Consultants include: The bolt heads lie on a reference base plate or a reference washer.

It can also be used in conjunction with FEA when a transfer of fluid causes a resultant force that needs to be considered when doing structural analysis.


This service is not available if you are a URL user where you do not log in with an email address. Please first verify your email before subscribing to alerts. This will give you increased confidence in your fastener designs and manufacturing processes.


Already Subscribed to this document. A bolt that requires testing is screwed into the test bench and fixed with a reference bolt. They can also be used to cover larger holes.

From a standardisation viewpoint, this dilemma is unresolved.

The friction between roughened surfaces ios greater than between smooth ones. On some test benches the partial torque is measured in the thread, in others on the base. Coefficients of friction calculated according to ISO standard need to be regarded with caution, however. The respective complementary partial torque can be identified via subtraction. In cases where fluid flow is critical either gas or liquid CFD isl be used to optimize flow and minimize turbulence, or to predict how two different liquids are mixing, etc.

Monitoring Standards monitoring is a free service designed for you who wish to be alerted of changes to or new editions of the standards required in your work.

A very low total coefficient of friction runs the risk of the fastener working itself loose. The objective is to fix components to each other in a way that enables them to fulfil their function.

When tightening the bolt the clamp force, the rotation angle, the total torque and one of the two partial torques are measured.