HAMEG 8030 PDF

May 20, 2019 posted by

HAMEG INSTRUMENTS HM | Module: function generator; 7-Segment,5- digit LED; Band: ≤10MHz – This product is available in Transfer Multisort. F requency Range 50 mHz 10 MHz,. Output Voltage up to 10 Vpp (into 50 Ω). ☑ Waveforms: Sine Wave, Triangle, Square Wave, Pulse, DC. ☑ D istortion Factor. Funktionsgenerator HM Equipment HAMEG GmbH, Frankfurt, build ?, 4 pictures, 4 schematics, Germany, tubes, semiconductors, Service- or Lab.

Author: Kaktilar Mikakree
Country: Belize
Language: English (Spanish)
Genre: Career
Published (Last): 10 October 2018
Pages: 218
PDF File Size: 15.53 Mb
ePub File Size: 17.67 Mb
ISBN: 736-6-72142-632-9
Downloads: 83613
Price: Free* [*Free Regsitration Required]
Uploader: Vudora

Suritett levegovel kifujtam a port valamennyire.

Funktionsgenerator HM-8030-2

Set to DC coupling. Vasaroltam egy hameg es szkopot. F – Distortion adjustment Setting: In case of any complaint, attach a tag to the instrument with a description of the fault observed. HAMEG will repair or replace products, which prove to be defective during the warranty period. Instead, contact your nearest service center! Output amplitude and signal connection Adaptation in decade steps to the desired amplitude range is performed by the use of two attenuators with – 20dB each, which are activated by pushbuttons.

Do not appiy any DC voltage to 80030 out- put socket. If the trigger output is loaded with 50 ohms, the value falls far below the TTL level. D – 1 kHz square wave duty cycle 1. Frequencies are read out on a 4 digit LED display. Save this item to a new parts list.

HM8030 Function Generator Module

Full text of ” Hameg: If the BNC socket at the rear panel of the HM unit was in use before, the BNC cable should be discon- nected from the basic unit for safety reasons. Please enter a message. The specified adjustment sequence should be strictly observed.

  BIHAR ANJUMAN ORG HADITH SAHIH BUKHARI MUSLIM PDF

E – Hz square wave duty cycle Setting: This permits the user to change the sweep width. HM function generator module,5MHz. Adjust [4], until the negative pulse length equals the positive pulse length on the screen. The foregoing information relates to product sold on, or after, the date shown below.

With a 50 ohms load at the outputthe signal amplitude should still be The output impedance is 50 Q, and the max. Maximum output amplitude Setting: This file is downloadable free of charge: The individual positions are marked with the corresponding symbols.

In case of cleaning the module the red display pane jameg not come in contact with alcohol or methylated spirit.

Full text of “Hameg: hm 2”

If any measurement or calibration procedures are unavoidable on the opened-up instrument, these must only be carried out by qualified personnel acquainted with the danger involved. If you want to join us and get repairing help please sign in or sign up by completing a simple electrical test or write your question to the Message board without registration. In high signal volt- age ranges, it should be noted that the used terminating resistor must dissipate the corresponding effective power.

A negative DC voltage reduces the frequency. G – Accuracy rating of the frequency ranges Setting: Set the trigger edge con- trol slope of the oscilloscope to negative edge trigger- ing.

  INTRODUCTION TO COMPUTER SECURITY GOODRICH TAMASSIA PDF

Connect multimeter to TP1. Save to an existing parts list Save to a new parts list. Szeretnem tudni milyen vegyszerrel lehetne tokeletesen kitakaritani.

All outputs are short-circuit-proof. This voltage is also available in DC mode. Should there be any trans- portation damage, inform the supplier immediately and do not put the module into operation. Looking for other manual? The DVM should display 1 V or 0. Thank you for your feedback. Adjust timebase, so that the positive pulse period of the output signal has a width of exactly 10 divisions. The capaci- tance of this isolating capacitor should be selected in that way that the frequency response of the output sig- nal is not affected over the whole frequency range of the HM unit.

The mains plug of the HM should be inserted before connections are made to measuring circuits. It is TTL compat- ible and has a duty-factor of approx. De megremultem mennyi por volt benne.

HM Hameg | HM function generator module,5MHz | | RS Components

After removal of the two screws at the rear of the mod- ule, both chassis covers can be lifted. Good luck to the repair! Nevertheless, a component hxmeg fail, but only after a longer period of operation. The frequency ranges are adjusted in the following order: You could suffer a fatal electrical shock!