FUTABA 12Z MANUAL PDF

July 5, 2019 posted by

Instruction manual • Read online or download PDF • Futaba 12Z User Manual. Futaba 12Z User Manual • Motor • Futaba Accessories communication. Read online or download PDF • Page / • Futaba 12Z User Manual • Futaba Accessories communication.

Author: Nenos Jugar
Country: Hungary
Language: English (Spanish)
Genre: Art
Published (Last): 21 September 2012
Pages: 228
PDF File Size: 9.51 Mb
ePub File Size: 11.29 Mb
ISBN: 913-7-77933-961-2
Downloads: 93589
Price: Free* [*Free Regsitration Required]
Uploader: Gardasho

Futaha 39 Helicopter basic setting procedure etc. Page 34 digit, use the cursor lever to select the arrow symbol and move the arrow symbol by pushing the enter button.

Futaba 12Z User Manual

Page 41 Use this function when you want to suppress the torque generated by the changes in the pitch and speed of the main rotor during pitch operation. Page 14 Volume Digital trim This transmitter is equipped with digital trims. Page 17 CF card memory size is 32MB.

If you continue pressing it, the trim position starts to move faster. We immediately began to evaluate the backlog of Futaba parts and service requests, completing what could be done with available parts. Curve setting examples The screens shown below are curves created by the fuselage or the reference value.

Remember, if the predefined control suddenly This function only works with G3 or PCM receivers moves to a position you did not command, land at Normally, it is used with the high side and low side trim function. It is used when rudder is applied during roll maneuvers, knife edge, futaha.

  FOP DOCBOOK TO PDF

Function, Functions of linkage menu, Function change | Futaba 12Z User Manual | Page 55 /

Page 89 Setting method turn the data input dial to the left and push the enter The rate and curve of each servo can be set by calling each screen. Page 13 Mount the antenna by turning it clockwise until turns to pink color. In addition, when the trim position returns to the center, the tone will change. fuhaba

Page 86 Setting method [Fine tuning VR operation mode] turn the data input dial to the left and push the enter and counterclockwise, the mixing r a t e i n c r e a s 21z s a n d d e c r e a s e srespectively. For a description of the connection method, see “Receiver and Servos Connection”.

FUTABA 12Z Series Instruction Manual

For types, all settings will be lost. Throttle cut setting servos can be adjusted as needed.

The screen depends on the model type. Prior approval of the appropriate government authorities may be required. The frequency data can be button. If you would like, you can freely change combinations of servo output channels, functions aileron, elevator, etcand input controllers sticks, switches, trim levers and trim switches.

You can already preset. Page Curve setting operation This section describes the setting procedure of curves which are used with the AFR function and each Curve type selection Curve type selection 1.

The differential rate can also be adjusted according to the flying state by Note: The operation speed can be set in 2 ranges of slow speed flight and high speed operated as a safety function by setting 2 switches.

  BOB MINTZER 15 EASY JAZZ BLUES & FUNK ETUDES PDF

Page Curve setting examples actually creating a curve, enter the data specified The curves shown below were created by using per the aircraft or the reference value.

Futaba 12Z User Manual | Page /

Connect the receiver and servos to match the type used. If you later change model commands that apply to helicopters only.

Receiver and servo connection Connect the receiver and servos in accordance with the connection diagram shown below. Setting method turn the data input dial to the left and push the enter The rate and curve of each servo can be set by calling each screen. Never hold the antenna alone.

Adjust it so that the nose does not fytaba in the rudder direction. Swash Mix SWASH MIX Example of use The swash mix function is used to correct the swash plate in the aileron roll direction and elevator cyclic pitch corresponding to each undesirable tendencies in the roll direction operation of each condition.

Model addition and call Default uftaba assigns 1 model to the T12Z. Got it, continue to print. Table of Contents Add to my manuals Add.

12a

Setting of these 2 positions can be selected by switch. Model type Select the model type f r o m a m o n g a i r p l a n ehelicopter, glider, and motor glider.