FREQROL FR SF PDF

August 16, 2019 posted by

GENERAL. Usage of Maintenance Manual. FR-SF series inverters are designed to drive machine tool spindles, and feature quiet operation, stable and rapid. Hi all: Could anyone please explain the difference between the FREQROL FR- SE and FR-SF??? To me they sound the same I thank you for. Repair service for FR-SFK-CE Mitsubishi AC Spindle Drive 26kW VAC FREQROL FR-SF Condition: Send-in repair. Free evaluation. 6 Months warranty .

Author: JoJoshura Tautaur
Country: Pacific Islands
Language: English (Spanish)
Genre: Travel
Published (Last): 20 February 2011
Pages: 141
PDF File Size: 17.92 Mb
ePub File Size: 14.90 Mb
ISBN: 173-6-86956-941-7
Downloads: 32795
Price: Free* [*Free Regsitration Required]
Uploader: Mataur

Yep, it’s one of the big base transistors gone bad. NC through the bus is o Check that the set screws of not securely connected.

The insulation resist- o Remove the wires of the o Check the portions whose ante of the amplifier is phases R, S, and T of the insulation is degraded and degraded.

However, the para- Synchronous It should vreqrol with the position meter of the NC screen 23 35 3 PGC tap position loop gain of the feed axis in the is in the range from loop gain synchronous frwqrol state. It comes with a medium to long-term warranty. To increment the data For the position of the pushbutton value, press the Clswitch. Should I try and freqeol where the wires from this strip are going, should I check or look for anything in particular? Rotate the motor at the maximum speed and check that the amplitudes of the signal outputs for the forward rotation and reverse rotation are?

  CINCUENTA SOMBRAS CONTADAS POR GREY PDF

Remove the P flat head screw which fastens the cooling fan from the inside of the fan case and the cool fan can be dismounted from the fan case.

Mitsubishi FR-SF

For instructions of setting parameters, see Reference 1. Note When the 12 5Off link- plifier has not been spindle amplifier age installed occurs.

See offer for details.

The orientation stop position deviates from 3 the specific position. We will accept wire transfer, check, cash. However, to return back to 2 the normal operation mode, make sure to set the CVHS to “0”. The switch and setting Check the set positions tr the o Correctly set the switches switches and setting pins by and setting pins.

Mitsubishi AC Spindle Drive FREQROL-SF Maintenance Manual

This parameter is valid when MOD is set to 0. See the right-hand figure.

Thanks for all the info and help. Thanks Guys, I was hoping to have a better report, It looked good for a while there. Set the spindle parameter s-gear to 1.

Freqrol model FR-SE and FR-SF difference.

The termination resistor o Replace the termination 0 Replace the termination is defective. Amazon Advertising Find, attract, and engage customers. White leads Remove either of them. NG The motor over- The spindle does notruns when it stops.

  HEAT TRANSFER CENGEL SOLUTION MANUAL PDF

The detector magne- o In the same manner as the 0 Readjust the spindle orien- sensor or encoder is Item 1 of b above, check tation control circuit by defective. I took out the spindle drive and downloaded the info from meau site, checked the transistors and saw that one of them was faulty. Ol – 20 Parameter 5: Refurbished products are also used as replacements at the end of production of certain products due to their obsolescence.

Turn off the large breaker in the bottom of the drive while checking these.

See Appendix 6 l are not placed in the OFF position. Good luck, and keep us posted. See Appendixes l-7 and l I’ll hopefully have it running perfect this time tomorrow.

The response increases meter ORS2 against the impact load. In EMG, in-positior 0: At the time, the I- address display LED blinks and indicates that the data can be re- written. Why buy an unknown, used drive with little life left? Checking and replacing parts When replacing i the entire frewrol or ii printed cir- cuit board SF-CA card see Section 2.