EUROMAP 70 PDF

June 13, 2019 posted by

EUROMAP 70 Electrical Interface between Injection Moulding Views. 6 years ago. Euromap, · Electrical, · Interface, · Injection, · Moulding. Euromap 2: Mould Fixing Dimension for Injection Moulding Machines. Specific information .. Mechanical properties, , Mechanical restraints, The electric control M2C is used for large machines. – highest safety standards ( as per EN /EN ) – standardised integration via EUROMAP 70 interface.

Author: Kazrazshura Akijin
Country: Moldova, Republic of
Language: English (Spanish)
Genre: Politics
Published (Last): 24 February 2005
Pages: 84
PDF File Size: 13.87 Mb
ePub File Size: 13.66 Mb
ISBN: 881-7-18966-885-5
Downloads: 4003
Price: Free* [*Free Regsitration Required]
Uploader: Yojind

All signals except table 1: Eruomap Service Support Downloads Company. The mould halves are heated by the magnetic heating plate. For easy and safe mould change, roller bars with spring packs are installed below the magnetic plate.

Power is only required for about 2 seconds to magnetise clamp the system at the beginning. During the whole machining process, the control continuously monitors the parameters of the magnetic force, the position of the die die contact and the temperature. Inquiry – checklist for a quotation: There are no limits set to the geometric shape of the magnetic plates. euroomap

EUROMAP 70 – version 1.5

The system consists of two electro-permanent magnetic plates, a control, a remote control, a complete set of cables and mounting takes often only a few hours. Additional T-slots, mounting holes, stops and special dimensions are not a problem to us. Magnetic clamping plates for different sectors of industry as e.

This is intended to provide interchangeability. Figure 10 Magnetic clamping system eurpmap in Arburg C High concentration euroamp of the magnetic force close to the centring ring.

EUROMAP 70 – version

Quick die change on presses and automatic punching machines. In operation, the system works independently of any power supply. Figure 11 Magnetic clamping systems for an injection moulding machine of the company Krauss Maffei Closure force: The electric control M2C is used for large machines.

  ANATOMIA VETERINARIA DYCE SACK Y WENSING PDF

The magnetic clamping systems or clamping plates have been especially designed for injection moulding machines, rubber presses, die casting machines, mould carrier and presses for metal forming. This penetrates only a few millimetres into the die base plate and will therefore have no impact on the die and the products. Eurromap 13 Magnetic clamping systems for an injection moulding machine of the company Krauss Maffei Closure force: Plug on the injection moulding machine female.

Technical Recommendations

Safety of the magnetic clamping system: Unless otherwise noted, the switch contacts are switching the reference potential plug contacts: An indicator light on the remote control continuously shows the state of the system. Only to unclamp the die, electrical energy is required again. Clamping and unclamping of several dies at the same time within a second. Exact positioning on the machine table is ensured using 20H7 longitudinal and crosswise slots. Size and geometric shape can be freely designed as requested by the customer.

Figure 14 Magnetic clamping system for a vertical Arburg machine With double rotary table Clamping plate at the top and at the bottom. Figure 8 Magnet clamping system for an injection moulding machine of the company Engel Closure force: The technology of the magnetic clamping plates is based on the principle of an electro-permanent magnet and is thus safe, even in case of a pressure failure.

All signals which are not optional shall be supported by all injection moulding machines and magnetic clamping systems.

Magnetic clamping systems for deformation tools | Römheld GmbH Friedrichshütte

The system itself does not have any movable elements and is practically maintenance-free. For the injection moulding machine see Figure 2 and the magnetic clamping system see Figure 1 the plug contacts should be capable of taking a minimum eurlmap V and 10 A.

  DOMINIC LORDS OF SATYR PDF

The mains supply of the MCS is also specified. The product range “M-TECS” stands for magnetic clamping technology, that means clamping technology of the highest level and offers the following key advantages for the user: M-TECS function principle for horizontal design.

Eurokap very small moulds are safely clamped.

The interface to the press is always designed redundantly, is effected via potential-free contacts to stop or drive the machine. A supplied separate control in combination with the press control provides the required safety for man and machine.

The electric control Euomap is used for small and medium-sized machines. Control and signal exchange with requirements for high performance levels. Combinations with Hilma machine vices or Stark zero point clamping systems can be easily realised, as they all come from a single supplier. Figure 9 Long pole technology in a to injection moulding machine Closure force: Pin a2 and Table 2: M-TECS function principle for vertical design. All of the desired performance levels can be met. The contact making is either potential-free or related to a reference potential supplied to a contact of the plug mounted on the injection moulding machine or the euroomap clamping system see Tables 1 and 2.