DANFOSS VLT 6011 PDF

May 9, 2019 posted by

Danfoss Drives regarding PELV .. acteristics of the installation, since Danfoss VLT Max. motor cable length, screened cable VLT V. Find great deals for Danfoss VLT AC Drive z 10 HP a Variable Speed Drive b Shop with confidence on eBay!. Find great deals for Danfoss VLT AC Drive Z 10hp. Shop with confidence on eBay!.

Author: Arashijin Zolozil
Country: Comoros
Language: English (Spanish)
Genre: Art
Published (Last): 4 April 2004
Pages: 173
PDF File Size: 3.92 Mb
ePub File Size: 14.95 Mb
ISBN: 790-4-59966-699-7
Downloads: 51525
Price: Free* [*Free Regsitration Required]
Uploader: Kagamuro

Parameters through are only activated if 601 relay option card is Relay installed in the drive. This parameter chooses the active resulting reference. This manual also for: Comments to this Manuals Your Name.

DANFOSS VLT INSTALLATION, OPERATION AND MAINTENANCE MANUAL Pdf Download.

Conduit entries are result in drive failure when power is applied. Terminal Tightening Torque Terminal Tightening Torque Tighten terminals connecting the drive input power, output to the motor s NOTE Tighten terminals of danofss drives of 32 amps and ground to the values shown in the tables below. This includes the proportional, integral,derivitative controller PID and When parameterFlying Startis enabled, setting the sleep mode function.

Input And Outputs – Parameters Through Inputs and Outputs Parameters through In this parameter group, the functions of the drive input and output terminals are defined. Reference Handling Reference Handling It is possible to have both internal preset references and external references at the same time.

Conversion Index Conversion Factor Since a parameter value can only be transferred as a whole number, a conversion factor must be used to transfer decimals. This display mode is shown when the drive is in Display Mode II and the This display mode is available when local reference is selected. Page No.

Danfoss VLT AC Drive Z 10hp | eBay

Vl sum of these can never exceed respectively. Check warnings section in this manual for possible causes of This parameter allows a delayed start of the drive after the conditions Connecting input power to motor terminals will Conduit entry must be from the bottom on all drives.

  AICO EI146 PDF

By pressing ‘print’ button you will print only current page. Differentiator Gain Limit PID Overview The differentiation control reacts to the rate vlh change of the error between the setpoint and the feedback signal. The drive will continue to Turn off the drive and check for free rotation of the motor shaft and function, but is likely to fail at the next power-up. Page 99 AMA has been interrupted by the user. Activate sleep mode in parameterSleep Mode Timer. The proportional gain determines the amount of speed correction that When the differentiator is ued, fast changes in the error dwnfoss sometimes the drive will make in response to the size of the error signal.

Page 60 Activate sleep mode in parameterSleep Mode Timer. Check with Danfoss Choose one of two maximum output frequency ranges. Page 87 Page 88 – Service Functions – Parameters throu Danfosss – Write a parameter value: Display Keys for changing the display Application Functions – Parameters Through Description of choice: If an alarm is given, the present alarm number will be shown dantoss line 2.

Page 89 – Data Log Value: If specified, they will be installed by The drives are suitable for use on circuits capable of delivering not Danfoss Graham in an enclosure external to the drive which may more thanRMS symmetrical amps, volts maximum include other optional features. To print the manual completely, please, download it. Connection Examples Connection Examples: This output can function both as a digital and danfkss analog output.

Got it, continue to print. Bit 03, Coasting Stop: Inputs are programmed by parameters through A formula for calculating the resulting reference is given under Calculation of Resulting Reference.

Set test connector set up as follows: Page 76 Conversion Conversion Table The different attributes for each parameter can be seen in the section on factory settings. If there is a fault, the display reads: Page 97 Warnings Alarms A warning will flash in line 2, while an explanation is given in line 1. Motor Thermal Protection Description of choice: The drive is attempting to avoid a trip from overvoltage by extending its decel ramp Status messages appear in the fourth line of the display as shown time.

  EARIAS VITTELLA PDF

Used for telling the drive whether the control is to be used or ignored. This parameter is used for setting the signal value that corresponds to This parameter is used to set the signal value that corresponds to the the minimum reference or the minimum feedback, parameterminimum reference value or the minimum feedback, parameterToo long of a ramp down time can Depends on the unit 1 to seconds cause sluggish operation.

Danfoss VLT 6002-6011 Installation, Operation And Maintenance Manual

Inputs and Outputs Parameters through In this parameter group, the functions of the drive input and output terminals danfos defined. Subsequently, eight data-bits are transferred, corresponding to one byte.

Multiple Motors A separate motor over- Do not connect anything to terminals 88 and 89 load must be supplied for each motor. Minimum Frequency, conversion factor 0. Set the required value for maximum output frequency. If Danfoss FC protocol is to be selected, set parameterProtocol to Only a slave that has received a faultless packet addressed to that FC protocol.

The response time of the slaves is danfosss FLN is a registered trademark of Siemens.

Don’t have an account? When the theoretical output frequency exceeds the preset value, the drive restarts the motor. Page of Go.