BEARCAT BCT15X MANUAL PDF
The Uniden Bearcat BCT15X is the follow-up to Uniden’s premier analog mobile scanner, the manual for the radio is contained on a CD-ROM, in PDF format. DImage_/Manual/ (1 of 3)5/26/ .. This page applies to the following scanner(s): BCDXT BCT15X Uniden® and Bearcat® are registered trademarks of Uniden America Corporation. View and Download Uniden BCT15 owner’s manual online. scanner radio with You can adjust the level of the following tones: Key Beep, BearTracker Alert.
|Published (Last):||6 July 2014|
|PDF File Size:||15.42 Mb|
|ePub File Size:||17.61 Mb|
|Price:||Free* [*Free Regsitration Required]|
Uniden has put out this fabulous scanner that will do a multitude of scanning achievement and you are here to find out how. Organizing your quick keys will be the hardest part of the planning.
You have to hold on a channel first, to attenuate it. Page Range MHz Set Range POI manua, enter how far out from this location you want the scanner to alert you. For the purpose of broadcasting weather information, the NWS has divided the United States into regions by state and county or parish, where applicable then assigned a 6-digit FIPS code to identify each county or parish.
The scanner opens a dialog ‘ Storing Location ‘ to store your current location or ‘ Location Exists ‘, Accept?
Uniden BCT15 Owner’s Manual
Continue at ‘ Edit Name ‘ below. Attach a suitable mounted mobile antenna to the antenna jack on the back of the scanner. You could use this feature to give you quick, single-press access to your favorite systems. An overview of the features can also be viewed at my Trunking Radio Comparison Chart page. Press Hold to resume scanning. At ‘ Quick Freq Save?
Set Priority This setting controls whether the scanner treats the channel bdarcat a priority channel while scanning. To listen to any frequency under the marker Hold in either mode and scroll to the frequency.
Easier to Read BCTX Scanner Manual
I hereby absolve myself from anything that happens to anyone or the scanner as a result of the information you will be reading. Page Set Modulation — Set the modulation type for the paging signal.
If you still cannot get satisfactory results while using your scanner or if you want additional information, please call or write the Uniden Parts and Service Division. Refer to Auto Step Size chart to help find the bands in the menu. Change to a Type I scanner setup.
To toggle the volume offset for a channel Hold on the channel and press then 5 LVL. All systems, sites, or search ranges that have a different startup key assigned will be locked out. So, if you turned the scanner off in Close Call mode and turn it back on in Key-Safe mode, that’s the mode you’re stuck with.
Then see Creating Sites. No until STP is blinking then bearczt the scroll control to select the step size from kHz. Scroll to the frequency or press. Scroll to the system then press the number of the group quick key s you want to enable. Press the Scroll Control to lock the desired level until the time you desire to change it. Ignore – the scanner rounds all received ID’s down to the next interval of The following geographical values are typical of use you might find valuable while traveling.
Bear Tracker Warning System.
Infinite – you must press Hold after a page to resume standby mode. PRI flashes beaarcat the display when you select this mode. LTR systems typically do not have a dedicated control channel. With this feature Onwhen the scanner detects a Close Call signal while scanning, the scanner overrides the current audio with the Close Call hit. The red light flashes once then stays on for a weather or Bear Tracker alert.
Unlocked — amnual group is scanned. These should be entered as Motorola Standard and not P Car Two is driving Car One east. Care And Maintenance Do not use excessive amounts of water. Close Call Auto store. Enter the channel number and press MENU. To store frequencies or talk group IDs you find during Search and Store, you must first select a system where the frequencies or talk group IDs will be stored. Preemptive Priority Preemptive priority is a feature that works on Motorola systems.
Setting the Serial Port Speed Use this setting to control the data rate used for the front and back panel serial ports. You typically set the front port to match the speed used to communicate with your PC default bps and the back port to the speed used mnaual communicate with an attached GPS device default bps.
See also Set ID Format.
What Is Scanning What is Searching? The default setting is no number tag blank. In addition there are alert sirens and a series of tones whose volume are user selectable. Set Modulation conventional only This setting selects the modulation used for the channel. If you lose the satellite signal, you will see ‘ Searching for Satellite ‘ until the GPS unit reacquires a signal.
IDs are not really scanned. Remove the bracket if it is attached.