700 HN100 PDF

April 13, 2019 posted by

Allen-Bradley HN Allen-Bradley HN 8-Pin Screw Terminal Tube Base Socket For Use With Bulletin HR and HX Timing Relays. MPN: HN ✓. Screw Terminal Tube Base Sockets ± Panel or DIN Rail Mounting . Open Style construction. 8 pin for use with DPDT BuIIetin HA reIays, HT. SOCKET Bases-Sockets: Type – General Purpose Relay Socket; Socket Configuration – 8-Pin Octal; Poles – 2; Mounting – DIN Rail or Panel; Construction .

Author: Gardalkree Faerisar
Country: Sweden
Language: English (Spanish)
Genre: Health and Food
Published (Last): 6 December 2008
Pages: 223
PDF File Size: 6.33 Mb
ePub File Size: 9.18 Mb
ISBN: 869-3-76393-497-2
Downloads: 56083
Price: Free* [*Free Regsitration Required]
Uploader: Moogushakar

SSR input impedance varies with a change in input control voltage. We make every effort to describe the products we sell in full detail.

The SSR casing serves to dissipate heat. Reduction Factor Load applied to 1 contact. Set the value to at least ms contact output type. If you would like a firm quote please contact us. Timers Front Mounting Turn off email alerts. Needs continuous input power applied.

Contact closure provides signal to timer. Start, gate, and reset Input method No-voltage input contact short-circuit and open input Short-circuit ON impedance: Operating Control Voltage Range Max.

The buyer may complete the sale with the correct terms. If the count drops below 0, it becomes The bottom two DIP switch pins are used to select the time ranges. Relay contacts R hn100 state immediately and the time delay t begins. When the initiating contact closes, timing begins. We will pay the following shipping both ways on itemsreturned within 30 days on items which were not sold as-is Approximate Dimensions H1n00 units in millimeters unless otherwise indicated.

  CHP 446F PDF

700HN100 AB

Start, reset, gate Minimum input signal width: Install the relays so that they are adequately ventilated. Additional start signals during timing don’t reset timing or contacts.

T Power Start Output N. Reset Indicator orange 4. For one-shot output, an output will be made again for the duration of the output time setting once the power supply has resumed. First, we should point out that we only sell quality product and our return rate is less than 0. Relay contacts R change state after time delay t is complete.

Normal output operation will not jn100 possible if the set time is too short. Most products we sell have a serial number or some other way for us to tell it came from us. Also returns setting items.

Output On Voltage Drop 1.

Contacts change state immediately when start signal is applied. Unfollow socket 8 pin to stop getting updates on your eBay Feed.

When totalizing count value has reset, the PV is reset at the same time. The only online payment we accept is PayPal. A signal is generated by the HR timing relay, and is the same potential as the supply voltage of the timing relay.

  BOOK OF JASWANT SINGH ON JINNAH IN PDF

Items listed as “like new” are used items that have had very little use. Dimensions are not intended for manufacturing purposes.

When the input power is removed or reset signal is applied contacts return to the shelf state. For more recent exchange rates, please use the Universal Currency Converter. Insulation Characteristics The following requirements are fulfilled: If this equipment is used in a manner not specified by the manufacturer, the protection provided by the equipment may be impaired.

If the time range is 0 min, 0 h, 0. Items in search results. Item Location see all Item Location.

HN Ser D – Button & Relay

Other Consumer Electronics Additional start signals during timing do not reset timing or contacts. Shipments made to addresses with in the U. The timer is reset when the time is up.

If you are buying just one item: Trademarks not belonging to Rockwell Automation are property of their respective companies.